"0x0000012E" Stop error occurs when an application sends a 12-byte SCSI opcode to an iSCSI target in Windows Vista SP2, Windows Server 2008 SP2, Windows 7 SP1, and Windows Server 2008 R2 SP1

Assume that you connect to an iSCSI target by using Microsoft iSCSI Initiator on a computer that is running one of the following operating systems:

• Windows Vista Service Pack 2 (SP2)
• Windows Server 2008 SP2
• Windows 7 Service Pack 1 (SP1)
• Windows Server 2008 R2 SP1

When you run an application that sends a 12-byte SCSI read/write opcode to the iSCSI target, the computer crashes. Additionally, you receive a Stop error message that resembles following:

Notes

• This Stop error message describes an INVALID_MDL_RANGE issue.
• The parameters in this Stop error message vary, depending on the configuration of the computer and kind of issue that occurred.
• Not all "Stop 0x0000012E" errors are caused by this issue.

Hotfix information

A supported hotfix is available from Microsoft. However, this hotfix is intended to correct only the problem that is described in this article. Apply this hotfix only to systems that are experiencing the problem described in this article. This hotfix might receive additional testing. Therefore, if you are not severely affected by this problem, we recommend that you wait for the next software update that contains this hotfix.

If the hotfix is available for download, there is a "Hotfix download available" section at the top of this Knowledge Base article. If this section does not appear, contact Microsoft Customer Service and Support to obtain the hotfix.

Note If additional issues occur or if any troubleshooting is required, you might have to create a separate service request. The usual support costs will apply to additional support questions and issues that do not qualify for this specific hotfix. For a complete list of Microsoft Customer Service and Support telephone numbers or to create a separate service request, visit the following Microsoft website: Note The "Hotfix download available" form displays the languages for which the hotfix is available. If you do not see your language, it is because a hotfix is not available for that language.

Prerequisites

To apply this hotfix, you must be running one of the following operating systems:

• Windows Vista Service Pack 2 (SP2)
• Windows Server 2008 Service Pack 2(SP2)
• Windows 7 Service Pack 1 (SP1)
• Windows Server 2008 R2 SP1

For more information about how to obtain a Windows Vista service pack, click the following article number to view the article in the Microsoft Knowledge Base: For more information about how to obtain a Windows Server 2008 service pack, click the following article number to view the article in the Microsoft Knowledge Base: For more information about how to obtain a Windows 7 or a Windows Server 2008 R2 service pack, click the following article number to view the article in the Microsoft Knowledge Base:

Registry information

To apply this hotfix, you do not have to make any changes to the registry.

Restart requirement

You must restart the computer after you apply this hotfix.

Hotfix replacement information

This hotfix does not replace a previously released hotfix.

File information

The global version of this hotfix installs files that have the attributes that are listed in the following tables. The dates and the times for these files are listed in Coordinated Universal Time (UTC). The dates and the times for these files on your local computer are displayed in your local time together with your current daylight saving time (DST) bias. Additionally, the dates and the times may change when you perform certain operations on the files.

Windows Vista, Windows Server 2008, Windows 7 and Windows Server 2008 R2 file information notes

Important Windows Vista hotfixes and Windows Server 2008 hotfixes are included in the same packages. However, only "Windows Vista" is listed on the Hotfix Request page. To request the hotfix package that applies to one or both operating systems, select the hotfix that is listed under "Windows Vista" on the page. Windows 7 hotfixes and Windows Server 2008 R2 hotfixes are included in the same packages. However, hotfixes on the Hotfix Request page are listed under both operating systems. To request the hotfix package that applies to one or both operating systems, select the hotfix that is listed under "Windows 7/Windows Server 2008 R2" on the page. Always refer to the "Applies To" section in articles to determine the actual operating system that each hotfix applies to.

• The files that apply to a specific product, SR_Level (RTM, SPn), and service branch (LDR, GDR) can be identified by examining the file version numbers as shown in the following table.

  Version	Product	SR_Level	Service branch
  6.0.600 2. 22xxx	Windows Vista and Windows Server 2008	SP2	LDR
  6.1.760 1. 17xxx	Windows 7 and Windows Server 2008 R2	SP1	GDR
  6.1.760 1. 22xxx	Windows 7 and Windows Server 2008 R2	SP1	LDR

• Service Pack 1 is integrated into the release version of Windows Server 2008. Therefore, RTM milestone files apply only to Windows Vista. RTM milestone files have a 6.0.0000.xxxxxx version number.
• GDR service branches contain only those fixes that are widely released to address widespread, critical issues. LDR service branches contain hotfixes in addition to widely released fixes.
• The MANIFEST files (.manifest) and the MUM files (.mum) that are installed for each environment are listed separately in the "Additional file information for Windows Vista, Windows Server 2008, Windows 7 and for Windows Server 2008 R2" section. MUM files and MANIFEST files, and the associated security catalog (.cat) files, are extremely important to maintaining the state of the updated component. The security catalog files, for which the attributes are not listed, are signed with a Microsoft digital signature.

For all supported x86-based versions of Windows Vista and of Windows Server 2008

For all supported x86-based versions of Windows 7

For all supported x64-based versions of Windows Vista and of Windows Server 2008

For all supported x64-based versions of Windows 7 and of Windows Server 2008 R2

For all supported IA-64-based versions of Windows Server 2008

For all supported IA-64-based versions of Windows Server 2008 R2

Microsoft has confirmed that this is a problem in the Microsoft products that are listed in the "Applies to" section.

For more information about iSCSI Initiator, go to the following Microsoft website:
For more information about how to configure iSCSI Initiators, go to the following Microsoft website:
For more information about software update terminology, click the following article number to view the article in the Microsoft Knowledge Base:

Additional file information

Additional file information for Windows Vista, Windows Server 2008, Windows 7 and for Windows Server 2008 R2

Additional files for all supported x86-based versions of Windows Vista and of Windows Server 2008

Additional files for all supported x86-based versions of Windows 7

Additional files for all supported x64-based versions of Windows Vista and of Windows Server 2008

Additional files for all supported x64-based versions of Windows 7 and of Windows Server 2008 R2

Additional files for all supported IA-64-based versions of Windows Server 2008

Additional files for all supported IA-64-based versions of Windows Server 2008 R2