Microsoft KB Archive Search

Notice: This website is an unofficial Microsoft Knowledge Base (hereinafter KB) archive and is intended to provide a reliable access to deleted content from Microsoft KB. All KB articles are owned by Microsoft Corporation. Read full disclaimer for more details.

  1. Home
  2. You receive a unit of measure conversion error when you finish a production order that was created from planning in Microsoft Dynamics NAV

You receive a unit of measure conversion error when you finish a production order that was created from planning in Microsoft Dynamics NAV

View products that this article applies to.

RAPID PUBLISHING ARTICLES PROVIDE INFORMATION DIRECTLY FROM WITHIN THE MICROSOFT SUPPORT ORGANIZATION. THE INFORMATION THAT IS CONTAINED HEREIN IS CREATED IN RESPONSE TO EMERGING OR UNIQUE TOPICS, OR IS INTENDED TO SUPPLEMENT OTHER KNOWLEDGE BASE INFORMATION.

↑ Back to the top

This article applies to Microsoft Dynamics NAV for all countries and all language locales.

↑ Back to the top

Symptoms

When you finish a production order that was created from planning for an item in Microsoft Dynamics NAV 5.0 Service Pack 1 (SP1) and in Microsoft Dynamics NAV 2009 SP1, you receive the following error message:
Qty. to Handle (Base) in Tracking Specification for Item No. Item_number, Serial No.: , Lot No.: Lot_number is currently –n.nn it must be –n.nnn.

In this error message, Item_number represents an actual item number. Lot_number represents an actual lot number. n.nn and n.nnn represent actual amounts.

This problem occurs if the following conditions are true:
  • The backward flushing method is used for the item.
  • The item is lot tracked.
  • The unit of measure (UOM) rounding is used for calculations of the item.

↑ Back to the top

Cause

This problem occurs because the rounding is incorrect when you run the calculate plan from the planning worksheets during planning.

↑ Back to the top

Resolution

Hotfix information

A supported hotfix is now available from Microsoft. However, it is only intended to correct the problem that is described in this article. Apply it only to systems that are experiencing this specific problem. This hotfix may receive additional testing. Therefore, if you are not severely affected by this problem, we recommend that you wait for the next Microsoft Dynamics NAV service pack or the next version that contains this hotfix.

Note In special cases, charges that are ordinarily incurred for support calls may be canceled if a Technical Support Professional for Microsoft Dynamics and related products determines that a specific update will resolve your problem. The usual support costs will apply to additional support questions and issues that do not qualify for the specific update in question.

↑ Back to the top



Installation information

Microsoft provides programming examples for illustration only, without warranty either expressed or implied. This includes, but is not limited to, the implied warranties of merchantability or fitness for a particular purpose. This article assumes that you are familiar with the programming language that is being demonstrated and with the tools that are used to create and to debug procedures. Microsoft support engineers can help explain the functionality of a particular procedure, but they will not modify these examples to provide added functionality or construct procedures to meet your specific requirements.

Note Before you install this hotfix, verify that all Microsoft Navision client users are logged off the system. This includes Microsoft Navision Application Services (NAS) client users. You should be the only client user who is logged on when you implement this hotfix.

To implement this hotfix, you must have a developer license.

We recommend that the user account in the Windows Logins window or in the Database Logins window be assigned the "SUPER" role ID. If the user account cannot be assigned the "SUPER" role ID, you must verify that the user account has the following permissions:
  • The Modify permission for the object that you will be changing.
  • The Execute permission for the System Object ID 5210 object and for the System Object ID 9015 object.


Note You do not have to have rights to the data stores unless you have to perform data repair.

Code changes

Note Always test code fixes in a controlled environment before you apply the fixes to your production computers.

To install this hotfix, change the code in the Planning Component table (99000829) as follows:
  1. Change the code in the Routing Link Code – OnValidate trigger as follows:
    Existing code
    ...
                         //  Delete the following line. 
                    VALIDATE("Expected Quantity",ROUND(Quantity * PlanningNeeds,0.00001));
                                                     
                      "Due Date" := ReqLine."Starting Date";
    ...
    Replacement code
     ...
                       // Add the following line. 
                  VALIDATE("Expected Quantity",Quantity * PlanningNeeds);
                                                    
                      "Due Date" := ReqLine."Starting Date";
    ...
  2. Change the code in the Calculation Formula – OnValidate trigger as follows:
    Existing code
    ...
                                                    "Calculation Formula"::Weight:
                                   Quantity := ROUND(Weight * "Quantity per",0.00001);
                                END;
                                     //  Delete the following line. 
                                   "Quantity (Base)" := ROUND(Quantity * "Qty. per Unit of Measure",0.00001);
                                                                     
                                    VALIDATE("Expected Quantity",Quantity * PlanningNeeds);
                                  END;
    ...
    Replacement code
    ...
                                                     "Calculation Formula"::Weight:
                                        Quantity := ROUND(Weight * "Quantity per",0.00001);
                                      END;
                                            // Add the following line. 
                                          "Quantity (Base)" := Quantity * "Qty. per Unit of Measure";
                                                                  
                                           VALIDATE("Expected Quantity",Quantity * PlanningNeeds);
                                       END;
    ...

Prerequisites

You must have one of the following products installed to apply this hotfix:
  • Microsoft Dynamics NAV 2009 SP1
  • Microsoft Dynamics NAV 5.0 SP1

Removal information

You cannot remove this hotfix.

↑ Back to the top

Status

Microsoft has confirmed that this is a problem in the Microsoft products that are listed in the "Applies to" section.

↑ Back to the top

MICROSOFT AND/OR ITS SUPPLIERS MAKE NO REPRESENTATIONS OR WARRANTIES ABOUT THE SUITABILITY, THE RELIABILITY OR THE ACCURACY OF THE INFORMATION THAT IS CONTAINED IN THE DOCUMENTS AND THE RELATED GRAPHICS PUBLISHED ON THIS WEB SITE (THE “MATERIALS”) FOR ANY PURPOSE.

THE MATERIALS MAY INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS AND MAY BE REVISED AT ANY TIME WITHOUT NOTICE. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, MICROSOFT AND/OR ITS SUPPLIERS DISCLAIM AND EXCLUDE ALL REPRESENTATIONS, WARRANTIES, AND CONDITIONS WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING BUT NOT LIMITED TO REPRESENTATIONS, WARRANTIES, OR CONDITIONS OF TITLE, NON-INFRINGEMENT, SATISFACTORY CONDITION OR QUALITY, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE MATERIALS.

↑ Back to the top

Keywords: kbmbsquickpub, kbnoloc, kbmbscodefix, kbqfe, kbmbsmigrate, kberrmsg, kbsurveynew, kbnotautohotfix, kbmbsmanufacturing, kb, kbmbspartner

↑ Back to the top

Article Info
Article ID : 981373
Revision : 2
Created on : 9/20/2018
Published on : 9/20/2018
Exists online : False
Views : 292