A detailed description of the Data Execution Prevention (DEP) feature in Windows XP Service Pack 2, Windows XP Tablet PC Edition 2005, and Windows Server 2003

Hardware-enforced DEP

Hardware-enforced DEP marks all memory locations in a process as non-executable unless the location explicitly contains executable code. A class of attacks exists that tries to insert and run code from non-executable memory locations. DEP helps prevent these attacks by intercepting them and raising an exception.

Hardware-enforced DEP relies on processor hardware to mark memory with an attribute that indicates that code should not be executed from that memory. DEP functions on a per-virtual memory page basis, and DEP typically changes a bit in the page table entry (PTE) to mark the memory page.

Processor architecture determines how DEP is implemented in hardware and how DEP marks the virtual memory page. However, processors that support hardware-enforced DEP can raise an exception when code is executed from a page that is marked with the appropriate attribute set.

Advanced Micro Devices (AMD) and Intel have defined and shipped Windows-compatible architectures that are compatible with DEP.

Beginning with Windows XP SP2, the 32-bit version of Windows uses one of the following:

• The no-execute page-protection (NX) processor feature as defined by AMD.
• The Execute Disable Bit (XD) feature as defined by Intel.

To use these processor features, the processor must be running in Physical Address Extension (PAE) mode. However, Windows will automatically enable PAE mode to support DEP. Users do not have to separately enable PAE by using the /PAE boot switch.

Note Because 64-bit kernels are Address Windowing Extensions (AWE) aware, there is not a separate PAE kernel in 64-bit versions of Windows.
For more information about PAE and AWE in Windows Server 2003, click the following article number to view the article in the Microsoft Knowledge Base:

283037 Large memory support is available in Windows Server 2003 and in Windows 2000

back to top

Software-enforced DEP

An additional set of Data Execution Prevention security checks have been added to Windows XP SP2. These checks, known as software-enforced DEP, are designed to block malicious code that takes advantage of exception-handling mechanisms in Windows. Software-enforced DEP runs on any processor that can run Windows XP SP2. By default, software-enforced DEP helps protect only limited system binaries, regardless of the hardware-enforced DEP capabilities of the processor.

back to top

Benefits

The primary benefit of DEP is that it helps prevent code execution from data pages, such as the default heap pages, various stack pages, and memory pool pages. Typically, code is not executed from the default heap and the stack. Hardware-enforced DEP detects code that is running from these locations and raises an exception when execution occurs. If the exception is unhandled, the process will be stopped. Execution of code from protected memory in kernel mode causes a Stop error.

DEP can help block a class of security intrusions. Specifically, DEP can help block a malicious program in which a virus or other type of attack has injected a process with additional code and then tries to run the injected code. On a system with DEP, execution of the injected code causes an exception. Software-enforced DEP can help block programs that take advantage of exception-handling mechanisms in Windows.


back to top

System-wide configuration of DEP

DEP configuration for the system is controlled through switches in the Boot.ini file. If you are logged on as an administrator, you can now easily configure DEP settings by using the System dialog box in Control Panel.

Windows supports four system-wide configurations for both hardware-enforced and software-enforced DEP.Hardware-enforced and software-enforced DEP are configured in the same manner. If the system-wide DEP policy is set to OptIn, the same Windows core binaries and programs will be protected by both hardware-enforced and software-enforced DEP. If the system cannot use hardware-enforced DEP, the Windows core binaries and programs will be protected only by software-enforced DEP.

Similarly, if the system-wide DEP policy is set to OptOut, programs that have been exempted from DEP protection will be exempted from both hardware-enforced and software-enforced DEP.

The Boot.ini file settings are as follows:Note policy_level is defined as AlwaysOn, AlwaysOff, OptIn, or OptOut.

Existing /noexecute settings in the Boot.ini file are not changed when Windows XP SP2 is installed. These settings are also not changed if a Windows operating system image is moved across computers with or without hardware-enforced DEP support.

During installation of Windows XP SP2 and Windows Server 2003 SP1 or later versions, the OptIn policy level is enabled by default unless a different policy level is specified in an unattended installation. If the /noexecute=policy_level setting is not present in the Boot.ini file for a version of Windows that supports DEP, the behavior is the same as if the /noexecute=OptIn setting was included.

If you are logged on as an administrator, you can manually configure DEP to switch between the OptIn and OptOut policies by using the Data Execution Prevention tab in
System Properties. The following procedure describes how to manually configure DEP on the computer:

1. Click Start, click Run, type sysdm.cpl, and then click
   OK.
2. On the Advanced tab, under
   Performance, click Settings.
3. On the Data Execution Prevention tab, use one of the following procedures:
   
   • Click Turn on DEP for essential Windows programs and services only to select the OptIn policy.
   • Click Turn on DEP for all programs and services except those I select to select the OptOut policy, and then click
     Add to add the programs that you do not want to use the DEP feature.
4. Click OK two times.

IT professionals can control system-wide DEP configuration by using a variety of methods. The Boot.ini file can be modified directly with scripting mechanisms or with the Bootcfg.exe tool that is included in Windows XP SP2.

To configure DEP to switch to the AlwaysOn policy by using the Boot.ini file, follow these steps:

1. Click Start, right-click My Computer, and then click Properties.
2. Click the Advanced tab, and then click Settings under the Startup and Recovery field.
3. In the System startup field, click Edit. The Boot.ini file opens in Notepad.
4. In Notepad, click Find on the Edit menu.
5. In the Find what box, type /noexecute, and then click Find Next.
6. In the Find dialog box, click Cancel.
7. Replace policy_level with AlwaysOn.
   
   WARNING Make sure that you enter the text accurately. The Boot.ini file switch should now read:
   /noexecute=AlwaysOn
8. In Notepad, click Save on the File menu.
9. Click OK two times.
10. Restart the computer.

For unattended installations of Windows XP SP2 or later versions, you can use the Unattend.txt file to pre-populate a specific DEP configuration. You can use the OSLoadOptionsVar entry in the [Data] section of the Unattend.txt file to specify a system-wide DEP configuration.

back to top

Per-program DEP configuration

For the purposes of program compatibility, you can selectively disable DEP for individual 32-bit programs when DEP is set to the OptOut policy level. To do this, use the Data Execution Prevention tab in
System Properties to selectively disable DEP for a program. For IT professionals, a new program compatibility fix that is named DisableNX is included with Windows XP SP2. The DisableNX compatibility fix disables Data Execution Prevention for the program that the fix is applied to.

The DisableNX compatibility fix can be applied to a program by using the Application Compatibility Toolkit. For more information about Windows application compatibility, see Windows Application Compatibility on the following Microsoft Web site:back to top