The Cluster service takes about 30 seconds to fail over IPv6 IP addresses in Windows Server 2008 R2

Consider the following scenario,

• You create a failover cluster on some computers that are running Windows Server 2008 R2.
• An IP version 6 (IPv6) IP address fails over from one cluster node to another cluster node.

In this scenario, the Cluster service takes about 30 seconds to fail over the IPv6 IP address. This causes clients to wait for about 30 seconds to reconnect to the IPv6 IP address.

This issue occurs because the Cluster service only sends gratuitous Neighbor Advertisement messages for IP version 4 (IPv4) IP addresses, and not for IPv6 IP addresses.

To resolve this issue, install the following hotfix package on the affected cluster nodes that are running Windows Server 2008 R2. After you install the following hotfix package, the failover time for IPv6 IP addresses is reduced to several seconds.

Hotfix information

A supported hotfix is available from Microsoft. However, this hotfix is intended to correct only the problem that described in this article. Apply this hotfix only to systems that are experiencing the problem described in this article. This hotfix might receive additional testing. Therefore, if you are not severely affected by this problem, we recommend that you wait for the next software update that contains this hotfix.

If the hotfix is available for download, there is a "Hotfix download available" section at the top of this Knowledge Base article. If this section does not appear, contact Microsoft Customer Service and Support to obtain the hotfix.

Note If additional issues occur or if any troubleshooting is required, you might have to create a separate service request. The usual support costs will apply to additional support questions and issues that do not qualify for this specific hotfix. For a complete list of Microsoft Customer Service and Support telephone numbers or to create a separate service request, visit the following Microsoft website: Note The "Hotfix download available" form displays the languages for which the hotfix is available. If you do not see your language, it is because a hotfix is not available for that language.

Prerequisites

To apply this hotfix, you must be running one of the following operating systems:

• Windows Server 2008 R2
• Windows Server 2008 R2 Service Pack 1 (SP1)

For more information about how to obtain a Windows Server 2008 R2 service pack, click the following article number to view the article in the Microsoft Knowledge Base:

Registry information

To use the hotfix in this package, you do not have to make any changes to the registry.

Restart requirement

You must restart the computer after you apply this hotfix.

Hotfix replacement information

This hotfix does not replace a previously released hotfix.

File information

The global version of this hotfix installs files that have the attributes that are listed in the following tables. The dates and the times for these files are listed in Coordinated Universal Time (UTC). The dates and the times for these files on your local computer are displayed in your local time together with your current daylight saving time (DST) bias. Additionally, the dates and the times may change when you perform certain operations on the files.

Windows Server 2008 R2 file information notes

Important Windows 7 hotfixes and Windows Server 2008 R2 hotfixes are included in the same packages. However, hotfixes on the Hotfix Request page are listed under both operating systems. To request the hotfix package that applies to one or both operating systems, select the hotfix that is listed under "Windows 7/Windows Server 2008 R2" on the page. Always refer to the "Applies To" section in articles to determine the actual operating system that each hotfix applies to.

• The files that apply to a specific product, SR_Level (RTM, SPn), and service branch (LDR, GDR) can be identified by examining the file version numbers as shown in the following table.

  Version	Product	SR_Level	Service branch
  6.1.760 0 . 21xxx	Windows Server 2008 R2	RTM	LDR
  6.1.760 1 . 21xxx	Windows Server 2008 R2	SP1	LDR

• The MANIFEST files (.manifest) and the MUM files (.mum) that are installed for each environment are listed separately in the "Additional file information for Windows Server 2008 R2" section. MUM and MANIFEST files, and the associated security catalog (.cat) files, are extremely important to maintain the state of the updated components. The security catalog files, for which the attributes are not listed, are signed with a Microsoft digital signature.

For all supported x64-based versions of Windows Server 2008 R2

For all supported IA-64�based versions of Windows Server 2008 R2

Microsoft has confirmed that this is a problem in the Microsoft products that are listed in the "Applies to" section.

For more information about software update terminology, click the following article number to view the article in the Microsoft Knowledge Base: For more information about a similar issue, click the following article number to view the article in the Microsoft Knowledge Base:

Additional file information

Additional file information for Windows Server 2008 R2

Additional files for all supported x64-based versions of Windows Server 2008 R2

Additional files for all supported IA-64�based versions of Windows Server 2008 R2