Notice: This website is an unofficial Microsoft Knowledge Base (hereinafter KB) archive and is intended to provide a reliable access to deleted content from Microsoft KB. All KB articles are owned by Microsoft Corporation. Read full disclaimer for more details.

How to enable debug mode for Remote Install Servers


View products that this article applies to.

This article was previously published under Q236033


IMPORTANT: This article contains information about modifying the registry. Before you modify the registry, make sure to back it up and make sure that you understand how to restore the registry if a problem occurs. For information about how to back up, restore, and edit the registry, click the following article number to view the article in the Microsoft Knowledge Base:
256986 (http://support.microsoft.com/kb/256986/EN-US/ ) Description of the Microsoft Windows Registry

↑ Back to the top


Summary

You can enable a Windows 2000 Remote Install Server (RIS) to run in Debug mode for troubleshooting purposes. This can be useful when you are trying to troubleshoot client/server issues (such as pre-staged systems not connecting to the RIS server, or clients not receiving information sent to or from the RIS server).
There are two debugging modes that you can enable. The first is Normal Debug mode, which logs output to a file. The other is Full Debug mode, which displays output via NTSD or Kernel Debugger. Both of these options require manual editing of the registry.

Setting RIS for Normal Debug Mode

Normal Debug mode enables the BinlSvc (Boot information Negotiation Layer) service to log information to a %SystemRoot%\Debug\Binlsvc.log file. To enable this mode:
  1. Using the Computer Management snap-in, expand Services and Applications, and then click Services. Locate and stop the Boot Information Negotiation Layer service. Or, you can stop the service by typing the following line at a command prompt:
    net stop binlsvc
    Note If DHCP services are also running on the RIS server, you must stop the DHCP services so that the binlsvc will be able to properly initialize the debug log.
  2. Start Registry Editor (Regedt32.exe).
  3. Locate the following key in the registry:
    HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Binlsvc\Parameters
  4. On the Edit menu, point to New, click DWORD Value, and then add the following registry value:
    Value Name: Debug
    Data Type: Reg_Dword
    Value: 0x80FFFFFF
  5. Quit Registry Editor.
  6. Start the Binlsvc service. Start DHCP services if they were stopped in step 1. To start the services, use the Computer Management snap-in or type the following lines at a command prompt. Press ENTER after each line.
    net start binlsvc
    net start "DHCP Client"
View the Binlsvc service output in the %SystemRoot%\Debug\Binlsvc.log file to assist in troubleshooting.

NOTE: The output log file does not have standard control characters. If you use a text viewer such as Notepad.exe the file may be difficult to read. You may want to stop the Binlsvc service again and view the file with Write.exe or WordPad.exe.

Setting RIS for Full Debug Mode

Full Debug mode sends information out an NTSD window on the console. Most problems can be solved by using the first debug method, but in rare cases in which more debug information is required you can use the method outlined below.
  1. Using the Computer Management snap-in, expand Services and Applications, and then click Services. Locate and stop the Boot Information Negotiation Layer service. Or, you can stop the service by typing the following line at a command prompt:
    net stop binlsvc
  2. Start Registry Editor (Regedt32.exe).
  3. Locate and click the following key in the registry:
    HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Binlsvc\Parameters
  4. On the Edit menu, point to New, click DWORD Value, and then add the following registry value:
    Value Name: Debug
    Data Type: Reg_Dword
    Value: 00FFFFFF
  5. Locate the ImagePath value under the following key in the registry:
    HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Binlsvc
    By default, the setting for the ImagePath value is "%SystemRoot%\System32\tcpsvcs.exe"
  6. On the Edit menu, click String, type ntsd -g -G %SystemRoot%\System32\tcpsvcs.exe, and then click OK.
  7. Verify that the ImagePath value contains the new setting.
  8. Quit Registry Editor.
  9. Using the Computer Management snap-in, expand Services and Applications, and then click Services.
  10. Double-click the Boot Information Negotiation Layer service, click the Logon tab, and then click to select Allow Service to interact with desktop.
  11. Start the Binlsvc service by either using the Computer Management snap-in or by typing the following line at a command prompt:
    net start binlsvc
Try to reproduce the problem. When the problem occurs, look for errors creating machine accounts and LDAP errors.

↑ Back to the top


Keywords: KB236033, kbhowtomaster, kbenv

↑ Back to the top

Article Info
Article ID : 236033
Revision : 8
Created on : 11/1/2006
Published on : 11/1/2006
Exists online : False
Views : 540