Notice: This website is an unofficial Microsoft Knowledge Base (hereinafter KB) archive and is intended to provide a reliable access to deleted content from Microsoft KB. All KB articles are owned by Microsoft Corporation. Read full disclaimer for more details.

How To Get the MAC Address for an Ethernet Adapter


This article demonstrates how to get the Media Access Control (MAC) address for an ethernet adapter programmatically by using NetBIOS, if your card is bound to NetBIOS.

↑ Back to the top

More Information

To get the Media Access Control (MAC) address for an ethernet adapter programmatically, use the Netbios() NCBASTAT command and provide a "*" as the name in the NCB.ncb_CallName field. This is demonstrated in the sample code below.

For computers with multiple network adapters you need to enumerate the LANA numbers and perform the NCBASTAT command on each. Even when you have a single network adapter, it is a good idea to enumerate valid LANA numbers first and perform the NCBASTAT on one of the valid LANA numbers. It is considered bad programming to hardcode the LANA number to 0.

In addition, other hardware and software may be assigned their own MAC addresses. For example, a modem can have a MAC address. Also, a RAS client or server can install "dummy" network adapters that correspond to a dialup or serial connection. Normally, these MAC addresses are randomly generated. If an adapter status is called on a LANA that corresponds to one of these adapters when no connection is present, Netbios returns error 0x34 (NRC_ENVNOTDEF) even if a reset was previously performed.

With the NetBEUI and IPX transports, the same information can be obtained at a command prompt by using:

net config workstation
The ID given is the MAC address.

The following code enumerates all LANA numbers, performs a reset (NCBREST), and an adapter status (NCBASTAT).

Sample Code

   #include <windows.h>
#include <wincon.h>
#include <stdlib.h>
#include <stdio.h>
#include <time.h>

typedef struct _ASTAT_

NAME_BUFFER NameBuff [30];


ASTAT Adapter;

void main (void)
NCB Ncb;
UCHAR uRetCode;
char NetName[50];
LANA_ENUM lenum;
int i;

memset( &Ncb, 0, sizeof(Ncb) );
Ncb.ncb_command = NCBENUM;
Ncb.ncb_buffer = (UCHAR *)&lenum;
Ncb.ncb_length = sizeof(lenum);
uRetCode = Netbios( &Ncb );
printf( "The NCBENUM return code is: 0x%x \n", uRetCode );

for(i=0; i < lenum.length ;i++)
memset( &Ncb, 0, sizeof(Ncb) );
Ncb.ncb_command = NCBRESET;
Ncb.ncb_lana_num = lenum.lana[i];

uRetCode = Netbios( &Ncb );
printf( "The NCBRESET on LANA %d return code is: 0x%x \n",
lenum.lana[i], uRetCode );

memset( &Ncb, 0, sizeof (Ncb) );
Ncb.ncb_command = NCBASTAT;
Ncb.ncb_lana_num = lenum.lana[i];

strcpy( Ncb.ncb_callname, "* " );
Ncb.ncb_buffer = (char *) &Adapter;
Ncb.ncb_length = sizeof(Adapter);

uRetCode = Netbios( &Ncb );
printf( "The NCBASTAT on LANA %d return code is: 0x%x \n",
lenum.lana[i], uRetCode );
if ( uRetCode == 0 )
printf( "The Ethernet Number on LANA %d is:
Adapter.adapt.adapter_address[5] );


↑ Back to the top

Keywords: kbapi, kbhowto, kbnetbios, kbnetwork, kb

↑ Back to the top

Article Info
Article ID : 118623
Revision : 3
Created on : 4/20/2018
Published on : 4/20/2018
Exists online : False
Views : 103