Microsoft KB Archive Search

Notice: This website is an unofficial Microsoft Knowledge Base (hereinafter KB) archive and is intended to provide a reliable access to deleted content from Microsoft KB. All KB articles are owned by Microsoft Corporation. Read full disclaimer for more details.

  1. Home
  2. "0x000000D1" Stop error when you try to open the MPIO console on a computer that is running Windows Server 2008 SP2

"0x000000D1" Stop error when you try to open the MPIO console on a computer that is running Windows Server 2008 SP2

View products that this article applies to.

Symptoms

Assume that you remove all the paths to a storage area network (SAN) storage device from a computer that is running Windows Server 2008 Service Pack 2 (SP2). The storage arrays support asymmetric logical unit access (ALUA). When you try to perform one of the following operations, the computer crashes:
  • Open the Microsoft Multipath I/O (MPIO) console.
  • Switch to the MPIO tab in the Properties dialog box of a disk that is managed by MPIO.
  • Run the Mpclaim.exe command together with the -b, -v, or -d option from the command prompt.
Additionally, you receive a Stop error message that resembles the following:
STOP: 0x000000D1 (parameter1, parameter2, parameter3, parameter4)
Notes
  • This Stop error describes a DRIVER_IRQL_NOT_LESS_OR_EQUAL issue.
  • The parameters in this Stop error message vary, depending on the configuration of the computer.
  • Not all "Stop 0x000000D1" errors are caused by this issue.

↑ Back to the top

Cause

This issue occurs because the system does not perform a null check before dereferencing the target port of the device.

↑ Back to the top

Resolution

Hotfix information

A supported hotfix is available from Microsoft. However, this hotfix is intended to correct only the problem that is described in this article. Apply this hotfix only to systems that are experiencing the problem described in this article. This hotfix might receive additional testing. Therefore, if you are not severely affected by this problem, we recommend that you wait for the next software update that contains this hotfix.

If the hotfix is available for download, there is a "Hotfix download available" section at the top of this Knowledge Base article. If this section does not appear, contact Microsoft Customer Service and Support to obtain the hotfix.

Note If additional issues occur or if any troubleshooting is required, you might have to create a separate service request. The usual support costs will apply to additional support questions and issues that do not qualify for this specific hotfix. For a complete list of Microsoft Customer Service and Support telephone numbers or to create a separate service request, visit the following Microsoft website:
http://support.microsoft.com/contactus/?ws=support
Note The "Hotfix download available" form displays the languages for which the hotfix is available. If you do not see your language, it is because a hotfix is not available for that language.

Prerequisites

To apply this hotfix, you must be running Windows Server 2008 SP2.

For more information about how to obtain a Windows Server 2008 service pack, click the following article number to view the article in the Microsoft Knowledge Base:

968849 How to obtain the latest service pack for Windows Server 2008

Registry information

To apply this hotfix, you do not have to make any changes to the registry.

Restart requirement

You must restart the computer after you apply this hotfix.

Hotfix replacement information

This hotfix does not replace a previously released hotfix.
File information
The global version of this hotfix installs files that have the attributes that are listed in the following tables. The dates and the times for these files are listed in Coordinated Universal Time (UTC). The dates and the times for these files on your local computer are displayed in your local time together with your current daylight saving time (DST) bias. Additionally, the dates and the times may change when you perform certain operations on the files.
Windows Server 2008 file information notes
Important Windows Vista hotfixes and Windows Server 2008 hotfixes are included in the same packages. However, only "Windows Vista" is listed on the Hotfix Request page. To request the hotfix package that applies to one or both operating systems, select the hotfix that is listed under "Windows Vista" on the page. Always refer to the "Applies To" section in articles to determine the actual operating system that each hotfix applies to.
  • The files that apply to a specific product, SR_Level (RTM, SPn), and service branch (LDR, GDR) can be identified by examining the file version numbers as shown in the following table.
    VersionProductSR_LevelService branch
    6.0.600
    2.
    23xxx    		Windows Server 2008SP2LDR
  • The MANIFEST files (.manifest) and the MUM files (.mum) that are installed for each environment are

    listed separately in the "Additional file information for Windows Server 2008" section. MUM files and MANIFEST files, and the associated security catalog (.cat) files, are extremely important to maintaining the state of the updated component. The security catalog files, for which the attributes are not listed, are signed with a Microsoft digital signature.
For all supported x86-based versions of Windows Server 2008
File nameFile versionFile sizeDateTimePlatform
Msdsm.sys6.0.6002.2318592,09608-Aug-201310:42x86
For all supported x64-based versions of Windows Server 2008
File nameFile versionFile sizeDateTimePlatform
Msdsm.sys6.0.6002.23185111,55208-Aug-201312:12x64
For all supported IA-64-based versions of Windows Server 2008
File nameFile versionFile sizeDateTimePlatform
Msdsm.sys6.0.6002.23185276,92808-Aug-201312:12IA-64

↑ Back to the top

Status

Microsoft has confirmed that this is a problem in the Microsoft products that are listed in the "Applies to" section.

↑ Back to the top

More Information

For more information about a similar issue in Windows Server 2008 R2 or Windows Server 2012, click the following article number to view the article in the Microsoft Knowledge Base:
2821052 "0x000000D1" Stop error when you open the MPIO snap-in on a computer that is running Windows Server 2008 R2 or Windows Server 2012

For more information about software update terminology, click the following article number to view the article in the Microsoft Knowledge Base:

824684 Description of the standard terminology that is used to describe Microsoft software updates

Additional file information

Additional file information for Windows Server 2008

Additional files for all supported x86-based versions of Windows Server 2008
File propertyValue
File nameX86_msdsm.inf_31bf3856ad364e35_6.0.6002.23185_none_cc65c263f20bf5bc.manifest
File versionNot applicable
File size1,664
Date (UTC)08-Aug-2013
Time (UTC)13:52
PlatformNot applicable
Additional files for all supported x64-based versions of Windows Server 2008
File propertyValue
File nameAmd64_msdsm.inf_31bf3856ad364e35_6.0.6002.23185_none_28845de7aa6966f2.manifest
File versionNot applicable
File size1,666
Date (UTC)08-Aug-2013
Time (UTC)13:52
PlatformNot applicable
Additional files for all supported IA-64-based versions of Windows Server 2008
File propertyValue
File nameIa64_msdsm.inf_31bf3856ad364e35_6.0.6002.23185_none_cc676659f209feb8.manifest
File versionNot applicable
File size1,665
Date (UTC)08-Aug-2013
Time (UTC)13:52
PlatformNot applicable

↑ Back to the top

Keywords: kb, kbautohotfix, kbqfe, kbhotfixserver, kbfix, kbsurveynew, kbexpertiseadvanced

↑ Back to the top

Article Info
Article ID : 2878031
Revision : 1
Created on : 1/7/2017
Published on : 12/15/2014
Exists online : False
Views : 776