Microsoft KB Archive Search

Notice: This website is an unofficial Microsoft Knowledge Base (hereinafter KB) archive and is intended to provide a reliable access to deleted content from Microsoft KB. All KB articles are owned by Microsoft Corporation. Read full disclaimer for more details.

  1. Home
  2. You receive an error message when you try to create a finance charge memo in the Swedish version of Microsoft Dynamics NAV 2009 SP1

You receive an error message when you try to create a finance charge memo in the Swedish version of Microsoft Dynamics NAV 2009 SP1

View products that this article applies to.

This article applies to Microsoft Dynamics NAV for the Sweden (se) language locale.

↑ Back to the top

Symptoms

Assume that you set the invoice rounding precision in General Ledger Setup and then set the additional fee on Finance Charge Terms to "0" in the Swedish version of Microsoft Dynamics NAV 2009 Service Pack 1 (SP1). When you try to create a finance charge memo, you receive the following error message:
The Finance Charge Memo Line already exists.

Identification fields and values: Finance Charge Memo No.=Finance Charge Memo_No.,Line No.=Line_NoSo is not possible to create Rounding Precision (LCY) in General Ledger Setup

↑ Back to the top

Resolution

Hotfix information

A supported hotfix is now available from Microsoft. However, it is only intended to correct the problem that is described in this article. Apply it only to systems that are experiencing this specific problem. This hotfix may receive additional testing. Therefore, if you are not severely affected by this problem, we recommend that you wait for the next Microsoft Dynamics NAV 2009 service pack or the next Microsoft Dynamics NAV version that contains this hotfix.

Note In special cases, charges that are ordinarily incurred for support calls may be canceled if a Technical Support Professional for Microsoft Dynamics and related products determines that a specific update will resolve your problem. The usual support costs will apply to additional support questions and issues that do not qualify for the specific update in question.

↑ Back to the top



Installation information

Microsoft provides programming examples for illustration only, without warranty either expressed or implied. This includes, but is not limited to, the implied warranties of merchantability or fitness for a particular purpose. This article assumes that you are familiar with the programming language that is being demonstrated and with the tools that are used to create and to debug procedures. Microsoft support engineers can help explain the functionality of a particular procedure, but they will not modify these examples to provide added functionality or construct procedures to meet your specific requirements.

Note Before you install this hotfix, verify that all Microsoft Navision client users are logged off the system. This includes Microsoft Navision Application Services (NAS) client users. You should be the only client user who is logged on when you implement this hotfix.

To implement this hotfix, you must have a developer license.

We recommend that the user account in the Windows Logins window or in the Database Logins window be assigned the "SUPER" role ID. If the user account cannot be assigned the "SUPER" role ID, you must verify that the user account has the following permissions:
  • The Modify permission for the object that you will be changing.
  • The Execute permission for the System Object ID 5210 object and for the System Object ID 9015 object.


Note You do not have to have rights to the data stores unless you have to perform data repair.

Code changes

Note Always test code fixes in a controlled environment before you apply the fixes to your production computers.
To resolve this problem, follow these steps:
  1. Change the code in the InsertLines function in the Finance Charge Memo Header table (302) as follows:
    Exsiting code
    ...
          TESTFIELD("Fin. Charge Terms Code");
          FinChrgTerms.GET("Fin. Charge Terms Code");
          IF FinChrgTerms."Additional Fee (LCY)" <> 0 THEN BEGIN//old line
          FinChrgMemoLine.RESET;
          FinChrgMemoLine.SETRANGE("Finance Charge Memo No.","No.");
          FinChrgMemoLine."Finance Charge Memo No." := "No.";
          IF FinChrgMemoLine.FIND('+') THEN
            NextLineNo := FinChrgMemoLine."Line No."
           ELSE
            NextLineNo := 0;
            IF (FinChrgMemoLine.Type <> FinChrgMemoLine.Type::" ") OR
    ...
    Replacement code
    ...
          TESTFIELD("Fin. Charge Terms Code");
          FinChrgTerms.GET("Fin. Charge Terms Code");
          FinChrgMemoLine.RESET;
          FinChrgMemoLine.SETRANGE("Finance Charge Memo No.","No.");
          FinChrgMemoLine."Finance Charge Memo No." := "No.";
          IF FinChrgMemoLine.FIND('+') THEN
            NextLineNo := FinChrgMemoLine."Line No."
           ELSE
            NextLineNo := 0;
          IF FinChrgTerms."Additional Fee (LCY)" <> 0 THEN BEGIN//new line
            IF (FinChrgMemoLine.Type <> FinChrgMemoLine.Type::" ") OR
    ...
  2. Change the code in the FinanceChargeRounding function in the Finance Charge Memo Headertable (302) as follows:
    Exsiting code
    ...
          IF FinanceChargeRoundingAmount <> 0 THEN BEGIN
            CustPostingGr.GET(FinanceChargeHeader."Customer Posting Group");
            CustPostingGr.TESTFIELD("Invoice Rounding Account");
            WITH FinChrgMemoLine DO BEGIN
              INIT;
              VALIDATE(Type,Type::"G/L Account");
              "System-Created Entry" := TRUE; 
    ...
    Replacement code
    ...
         IF FinanceChargeRoundingAmount <> 0 THEN BEGIN
            CustPostingGr.GET(FinanceChargeHeader."Customer Posting Group");
            CustPostingGr.TESTFIELD("Invoice Rounding Account");
            WITH FinChrgMemoLine DO BEGIN
              NextLineNo := NextLineNo + 10000;//new line
              INIT;
              "Line No." := NextLineNo;//new line
              VALIDATE(Type,Type::"G/L Account");
              "System-Created Entry" := TRUE;
    ...

Prerequisites

You must have the Swedish version of Microsoft Dynamics NAV 2009 Service Pack 1 (SP1) installed to apply this hotfix.

Removal information

You cannot remove this hotfix.

↑ Back to the top

Status

Microsoft has confirmed that this is a problem in the Microsoft products that are listed in the "Applies to" section.

↑ Back to the top

Note This is a "FAST PUBLISH" article created directly from within the Microsoft support organization. The information contained herein is provided as-is in response to emerging issues. As a result of the speed in making it available, the materials may include typographical errors and may be revised at any time without notice. See Terms of Use for other considerations.

↑ Back to the top

Keywords: kberrmsg, kbnoloc, kbsurveynew, kbmbscodefix, kbmbspartner, kbmbsmigrate, kb, kbqfe, kbmbsquickpub

↑ Back to the top

Article Info
Article ID : 2276067
Revision : 2
Created on : 9/21/2018
Published on : 9/21/2018
Exists online : False
Views : 306